How to fight mold in the apartment

Many of us believe that mold on the walls of the apartment can appear because of not clean enough tenants who do not ventilate and clean the apartment in time. However, this filth can affect very neat people and its appearance does not depend on the frequency of cleaning. These microorganisms can appear unexpectedly, and it is very difficult to get rid of them. But if you seriously think about how to get rid of mold in the apartment, you can get not bad results.

Where do unkempt stains on walls and other surfaces come from? From the air. Mold spores are carried by air currents and as soon as they hit a damp surface, immediately begin to divide with great speed. This process can only be stopped by a determined and relentless fight against mold.

Causes of mold in the apartment

Why is there dampness in the apartment and with it mold? The reason may be poor ventilation in the bathroom, toilet or kitchen, as well as insufficient air circulation and ventilation of the apartment, especially after the installation of new airtight double-glazed windows.

Your home may have a leaky roof or water collecting in the basement. Another reason is the very fast pace of building the house, which resulted in a violation of construction techniques and drying requirements. Then the appearance of mold on the walls is guaranteed.

The fight against mold and its removal from the walls and other surfaces in the apartment should be started immediately, as it is very dangerous to human health. In addition, when mold affects the walls, the mold fibers penetrate deep into the brick or concrete and it is much more difficult to fight such an affection. Over time, the load-bearing capacity of the structure is reduced, but tenants are more concerned about the aesthetic side of the problem. Walls affected by fungus look disgusting.

An unpleasant and musty musty smell arises as a result of microorganisms, although you can get the feeling that no one has cleaned the room in a long time.

How to get rid of it?

To combat mold requires cleaning the surface and then treating it with fungicidal agents, which in turn are divided into two types: for professional and domestic use. Professional products are usually used during construction, as they fight biocorrosion and penetrate deeply into the surface of the building material. They are tested for non-toxicity and hypoallergenic properties and packed in containers with detailed instructions for use. Such products are sold in concentrated form, while in some stores they can be diluted and ready to use.

Household mold remedies create a protective layer on the treated surface that will remain active in protecting against mold for several days. If the product is guanidine-based, it will remain active for several years.

In the fight against mold, it is very important to establish the cause of its appearance and eliminate it, otherwise you will have to fight the microorganisms constantly. In urban apartments, mold settles at high humidity, and you need to find out why the room is so damp.

Because of insufficient ventilation, mold stains appear on ceilings, walls and in the corners of the room. The main suppliers of steam are the kitchen, bathroom and bathroom. It is these rooms that are connected to the central ventilation of the building. Check to see if the draft is insufficient or if the duct is clogged with dust, cobwebs, and so on. Perhaps the neighbors have somehow blocked the air flow in the ventilation shaft.

In the bathroom and toilet there should be a ventilation gap of at least 1 cm between the threshold and the door. Maybe after another repair it was decided that this gap does not look aesthetically pleasing. In this case, you can install a special grille in the bottom of the door leaf.

For sufficient air circulation, there should be not only the draft in the ventilation shaft, but also the possibility of air inflow from the street. The latter is very problematic if the apartment installed airtight glazing. It decreases heat loss very effectively, of course, but it also blocks the incoming air masses from the outside. To ensure air circulation in the apartment, buy double-glazed windows with ventilation valves. If plastic windows are already installed, they can be equipped with ventilation devices. You can, in the end, simply ventilate the room 2-3 times a day.

If you are sure that mold is the cause of damp walls, contact the operating company of the house. They will shut off the excess moisture from the outside. And you will need to conduct a full-fledged cosmetic repair in the apartment with the removal of not only wallpaper, but also putty and plaster. Need to gain access to the bare wall and treat it with special agents of deep penetration. After drying, carry out finishing work on wallpapering or other means of finishing work.